Comparator

Optical Comparator Alternative Kestrel
Not the shadowy image of optical comparators. Kestrel a 2-axis, non-contact measurement system, purely optical high resolution image offering quality, accuracy, repeatability with speed.
www.visioneng.com

Voltage Comparator
Find electronics solutions for your business. Get it done now.
www.business.com

Voltage Comparator
Precision Dual/Quad cost effective Open Drain/Push Pull driver. Available at Mouser Electronics.
www.aldinc.com

File Folder Compare
File folder compare. Your Small Business Hub.
OfficeSupplies.Capital.com

Comparator - Wikipedia, the free encyclopedia
For other uses, see Comparator (disambiguation). In electronics, a comparator is a device which compares two voltages or currents ...
en.wikipedia.org

Warning: mkdir() [function.mkdir]: Permission denied in /home/webs/affiliatelib2/CacheManager.php on line 12

Warning: mkdir() [function.mkdir]: No such file or directory in /home/webs/affiliatelib2/CacheManager.php on line 12

Warning: fopen(/home/templatecore2cache//*cluesnet.com/ac/ac16f832348683ba67be8551b428c6d0d5d079ca.tc2cache) [function.fopen]: failed to open stream: No such file or directory in /home/webs/affiliatelib2/CacheManager.php on line 130

Warning: fwrite(): supplied argument is not a valid stream resource in /home/webs/affiliatelib2/CacheManager.php on line 131

Warning: fclose(): supplied argument is not a valid stream resource in /home/webs/affiliatelib2/CacheManager.php on line 132

In electronics, a comparator is a device which compares two voltages or current (electricity)s and switches its output to indicate which is larger. More generally, the term is also used to refer to a device that compares two items of data.

A dedicated voltage comparator will generally be faster than a general-purpose operational amplifier pressed into service as a comparator. A dedicated voltage comparator may also contain additional features such as an accurate, internal voltage reference and adjustable hysteresis.

Input voltage range The input voltages must not exceed the power voltage range: VS- ≤ V+,V- ≤ VS+.

In the case of TTL/CMOS logic output comparators negative inputs are not allowed: 0 ≤ V+,V- ≤ Vcc.

OP AMP implementation of voltage comparator A standard operational amplifier operating without negative feedback can be used as a comparator. When the non-inverting input (V+) is at a higher voltage than the inverting input (V-), the high gain of the op-amp causes it to output the most positive voltage it can. When the non-inverting input (V+) drops below the inverting input (V-), the op-amp outputs the most negative voltage it can. Since the output voltage is limited by the supply voltage, for an op-amp that uses a balanced, split supply, (powered by ± VS) this action can be written:

Vout = VS sgn(V+ − V−)

where sgn(x) is the signum function. Generally, the positive and negative supplies VS will not match absolute value: Vout V-) else VS- when (V+ < V-).

Equality of input values is very difficult to achieve in practice. The speed at which the change in output results from a change in input (often called the slew rate in operational amplifiers) is typically in the order of 10ns to 100ns, but can be as slow as a few tens of μs.

Dedicated voltage comparator chips A dedicated voltage comparator chip, such as the LM339, is designed to interface directly to digital logic (for example Transistor-transistor logic or CMOS). The output is a binary state, and it is often used to interface real world signals to digital circuitry (see analog to digital converter). If one of the voltages is fixed, for example because a DC adjustment is possible in a device earlier in the signal path, a comparator is just a cascade of amplifiers. When the voltage is nearly equal the output voltage would not fall into one of the logic levels, thus analog signals would enter the digital domain with unpredictable results. To make this range as small as possible the cascade is long and high gain, that is bipolar transistors instead of field effect transistors are used, except sometimes for the fist stage. For high speed the input impedance of the stages is made low. This already reduces the saturation of the slow, large P-n junction of the bipolar transistors, which would otherwise lead to long recovery times. Fast that is small Schottky diodes as in binary logic are applied to improve matters even further. Also like in binary logic the speed is not as high as if the amplifiers would be used for analog signals. Slew rate has no meaning for these devices. For the application in flash ADCs after each amplifier the signal can be fanned out over 8 ports matched to the voltage and current gain and resistors are used as level-shifters.

The LM339 accomplishes this with an open collector output. When the inverting input is at a higher voltage than the non inverting input, the output of the comparator is connected to the negative power supply. When the non inverting input is higher than the inverting input, the output is floating (has a very high impedance to ground).

With a pull-up resistor and a 0 to +5V power supply, the output takes on the voltages 0 or +5 and can be interfaced to Transistor-transistor logic logic: Vout V-) else 0.

Precautions in use When comparing a noisy signal to a threshold, the comparator may switch rapidly from state to state as the signal crosses the threshold. If this is unwanted, positive feedback forming a Schmitt trigger can be used to provide hysteresis and a cleaner output signal.

Applications

Constant fraction discriminator
Flash ADC